PERENCANAAN STRUKTUR GEDUNG LABORATORIUM TEKNIK ELEKTRO DAN TEKNIK PERENCANAAN WILAYAH
https://doi.org/10.58466/rigid.v2i1.1167
Keywords:
Building Structure Planning, Laboratory Building, StructureAbstract
The laboratory has an important role in supporting academic/non-academic activities, especially at the Faculty of Engineering, Universitas Swadaya Gunung Jati Cirebon. Along with the development of departments at the Faculty of Engineering, it is necessary to increase laboratory facilities are needed which are designed separately to facilitate educational activities. This study aims to plan and design the structure of the Electrical Engineering Laboratory and Urban Regional Planning Engineering building with a reinforced concrete structure type consisting of 4 floors with a floor height of 4 m. This building was built on Jl.Perjuangan (Additional Building Area), Sunyaragi, Kec. Kesambi, Cirebon City with a hard soil type which according to the earthquake resistance planning regulations for buildings (SNI 1726-2019) is included in the seismic design category D. The design of this building uses a special moment resisting frame system (SRPMK). The structural planning of this building includes plates, beams, columns and foundations following the reinforced concrete structural regulations (SNI 2847-2019). The earthquake load was calculated using the response spectrum method and then analyzed using the ETABS computer aided program
References
Y. Q. A. Empung, Agus W., “Perencanaan Struktur Gedung Laboratorium Vaksin PT. Bio Farma (PERSERO) Di Kota
Bandung,” Akselerasi J. Ilm. Tek. Sipil, vol. 1, no. 2, pp. 52–62, 2020.
M. Fahimmudin, “Perencanaan Gedung Laboratorium Fakultas Teknik Universitas 17 Agustus 1945 Samarinda,” J.
Keilmuan dan Apl. Tek. Sipil, vol. 1, no. 1, 2015.
N. Afriga, Wardi, and R. Mulyani, “Perencanaan Struktur Gedung Laboratorium Kampus LIPI Bandung Menggunakan
Struktur Rangka Pemikul Momen (SRPM),” vol. 2, no. 1, 2022.
Naratama, I. N. Sutarja, and I. W. Dana, “Perencanaan Struktur Beton Bertulang Gedung Bertingkat Menggunakan Sistem Rangka Pemikul Momen Khusus (Studi Kasus : Gedung Laboratorium Bersama Universitas Udayana),” J. Ilm. Tek.
Sipil, vol. 18, no. 1, pp. 9–18, 2014.
V. Itteridi and I. Shaleh, “Perencanaan Struktur Gedung 5 Lantai Dengan Analisis Program Etabs Kampus Sekolah
Tinggi Teknologi Pagar Alam (STTP),” J. Ilm. Bering’S, vol. 4, no. 1, pp. 16–25, 2017, doi: 10.36050/berings.v4i01.129.
S. U. Dewi and M. I. Pratama, “Analisa Perencanaan Struktur Beton Gedung Kuliah Kampus 2 IAIN Kota Metro
Menggunakan Program ETABS (Extended Three Analysis Building Systems),” TAPAK (Teknologi Apl. Konstr. J. Progr.
Stud. Tek. Sipil, vol. 7, no. 2, pp. 176–197, 2018, [Online]. Available: https://www.ojs.ummetro.ac.id/index.php/tapak/article/view/729
F. H. Jaya, F. Juwita, and S. A. DP, “Permodelan Desain Gedung Perkuliahan Fakultas Teknik Menggunakan Program
ETABS dan LUMION Pada Kampus Universitas Sang Bumi Ruwa Jurai,” pp. 111–122, 2020.
A. Purwanto and M. T. Prayogy, “Perencanaan Struktur Bangunan Gedung Hotel Horison Pekalongan,” J. Karya Tek.
Sipil, vol. 2, no. 2, 2013.
Badan Standarisasi Nasional Indonesia, “SNI 2847-2019 : Persyaratan Beton Struktural untuk Bangunan Gedung,” no. 8,
p. 720, 2019.
Badan Standarisasi Nasional Indonesia, “SNI 1726:2019 tentang Tata Cara Perencanaan Ketahanan Gempa Untuk
Struktur Bangunan Gedung dan Non Gedung,” Bsn, no. 8, p. 254, 2019.
Badan Standardisasi Nasional Indonesia, “SNI 1727:2013 tentang Beban Minimum untuk Perancangan Bangunan
Gedung dan Struktur Lain,” p. 196, 2013, [Online]. Available: www.bsn.go.id
